![]() Remember, the curved arm goes on the passenger side.ġ1) Install the 14mm wiper arm mounting bolts. Line them up with the tape on the windshield and push down on the serrated studs until fully seated. Fit them together loosely first and then insert and press the center part down until flush with the outer part.ġ0) Install the wiper arms. First sandwich it into position with the windshield, then snap the little molded in fasteners into their corresponding holes in the metal below.ħ) Snap the left side cover into place over the previously mounted right side cover.Ĩ) Fit the brake reservoir cover and the weatherstrip back into position.ĩ) Install the two corner panel fasteners. Mount the wiper arms and run it to check operation before final assembly.Ħ) Mount the right side cover. Snug them up until the vibration grommet starts to depress.ĥ) Plug in the wiring connector. Tighten up the 10mm assembly mounting bolts. It is far enough right when the bolt holes line up with the threaded holes below. Remember to start left and seat the rubber grommet at the rear into the slot and then move the linkage to the right. Since the linkage move as the nut is tightened, simply move it back to the park position when done.Ĥ) Mount the linkage in the car. Take care to align the linkage correctly on the motor shaftģ) Install the 12mm bolt on the motor shaft. Serrations on the linkage and motor shaft will lock these into position once seated. Remember, in the park position this linkage is directly behind, that is parallel, to the larger front-most linkage. It is important to maintain correct orientation here. Make sure the wiring is routed correctly and affix the plug and secure the wire with a wire tie.Ģ) Mount the linkage on the motor shaft. Unsnap the cover with an upward jerking motion.ġ) Install the three 10mm motor mounting bolts. Panel fastener detail: push down center and pry outside Then the longer left side cover can be removed along with the entire weatherstrip. How to Remove Rear Wiper Assembly (Tutorial) Post by A Psycho Martyr » Wed 8:04 am. Posts: 2598 Joined: Mon 2:13 pm Location: Cullman, Alabama. Unsnap the weatherstrip from this cover and to the right end of the right end cover. The Online Community for Pontiac Vibe Enthusiasts. ![]() Remove the small cover that is over the brake fluid reservoir. There are fasteners at intervals along it's length that are molded into the underside of the cover. Push down in the middle of this two part fastener and the pry up to remove the outer part. There are panel fasteners at each corner that must come off. The passenger side arm is curved at the bolt end.ĥ) Remove the left side black plastic part of the wiper cover. Protecting the stud threads with a nut is a good idea when tapping. Gently tapping with hammer on the end of the stud may jar them loose. Get Yours Today We have the best products at the right price. A layer of ice is known to have sharp edges that can reduce the effectiveness of the micro edge of the rubber wiper blade.2) Remove the protective plastic caps covering the wiper arm nuts.ģ) Use a 14mm socket and 3/8" ratchet to remove the wiper arm nuts.Ĥ) Remove the wiper arm. Equip cars, trucks & SUVs with 2007 Pontiac Vibe Wiper Blade (Windshield) from AutoZone. Another trick to enhance the longevity of your Vibe's wiper blades is to scrape off the ice and snow from the windshield before using your wipers. We recommend changing the wiper blades on your Vibe at least once a year even if you don't use your wipers much - the sun wears out your wiper blades more than using them to wipe water. Always replace both windshield wiper blades, even if only one side is streaking - the rubber on the opposite side is likely worn as well. Follow these steps to learn how to remove front windshield wipers in your 2009 Pontiac Vibe.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |